U-Boot 2009.08-00794-g5fa48ba-dirty-svn (10月 08 2015 - 12:40:07) CPU: Freescale i.MX6 family TO0.0 at 792 MHz Temperature: 39 C, calibration data 0x5774fe5f mx6q pll1: 792MHz mx6q pll2: 528MHz mx6q pll3: 480MHz mx6q pll8: 50MHz ipg clock : 66000000Hz ipg per clock : 66000000Hz uart clock : 80000000Hz cspi clock : 60000000Hz ahb clock : 132000000Hz axi clock : 198000000Hz emi_slow clock: 22000000Hz ddr clock : 396000000Hz usdhc1 clock : 198000000Hz usdhc2 clock : 198000000Hz usdhc3 clock : 198000000Hz usdhc4 clock : 198000000Hz Board: MX6SoloLite-NTX:[ POR ] Boot Device: SD I2C: ready DRAM: 512 MB MMC: csd is 0x400e0032, 0x5b590000, 0x3a917f80, 0xa400000 scr addr is 0x875fef08, switch_status addr is 0x875fee98 mmc0 is current device MMC read: dev # 0, block # 1023, count 1 ... 1 blocks read: OK MMC read: dev # 0, block # 1024, count 1 ... 1 blocks read: OK HW switch boot from ESD FSL_USDHC: 0,FSL_USDHC: 1,FSL_USDHC: 2 In: serial Out: serial Err: serial ntx_hw_late_init() i2c: I2C2 SDA is low, start i2c recovery... I2C2 Recovery success hw_anadig_reg_core=7c3e1f Device: FSL_USDHC Manufacturer ID: 1b OEM: 534d Name: 00000 Tran Speed: 50000000 Rd Block Len: 512 SD version 2.0 Clock: 50000000 High Capacity: Yes Capacity: 7861174272 Bytes Bus Width: 4-bit Boot Partition for boot: No boot partition available csd is 0x400e0032, 0x5b590000, 0x3a917f80, 0xa400000 scr addr is 0x875fef58, switch_status addr is 0x875feee8 ntx_config_fastboot_layout():8 binaries partition added ntx_config_fastboot_layout():3 mbr partition added Net: No ethernet found. 0 mmc0 is current device hwcfgp=8783920c,pcb=46,customer=9 RC5T619 [0xbd]=0x0 ESDin=0,UPGKey=-1,PWRKey=0,USBin=0 ram p=80000000,size=536870912 MMC read: dev # 0, block # 14335, count 1 ... 1 blocks read: OK MMC read: dev # 0, block # 14336, count 12883 ... 12883 blocks read: OK skip load "logo" because of overwrited MMC read: dev # 0, block # 34815, count 1 ... 1 blocks read: OK no "logo" bin header Kernel RAM visiable size=505M->505M MMC read: dev # 0, block # 2047, count 1 ... 1 blocks read: OK kernel size = 2665172 MMC read: dev # 0, block # 2048, count 5211 ... 5211 blocks read: OK MMC read: dev # 0, block # 1, count 1 ... 1 blocks read: OK hwcfg rootfstype : 2 hwcfg partition type : 2 ## Booting kernel from Legacy Image at 80800000 ... Image Name: a28e72_#4071 Jul 17 16:56:30 Created: 2015-07-17 8:56:33 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 2333364 Bytes = 2.2 MB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... drivers/misc/ntx-misc.c(msp430_i2c_probe): Can't allocate irq 395 [zForce_ir_touch_recv_data-275] command BootComplete (0)... PMU: ricoh61x_battery_probe : version is RICOH61x_BATTERY_VERSION: 2014.02.21 V3 .1.0.0-Solution1 2015/02/09 1+0 records in 1+0 records out 512 bytes (512B) copied, 0.000273 seconds, 1.8MB/s cannot open /dev/null dosfsck 3.0.6, 04 Oct 2009, FAT32, LFN /dev/mmcblk0p3: 320 files, 7459/827438 clusters [PROGRESS_BAR-3065] No progess ... (none) login: sh: you need to specify whom to kill killall: wpa_supplicant: no process killed dhcpcd[1057]: version 6.6.6 starting dhcpcd[1057]: eth0: using /sys hwaddr: 78:45:61:08:50:d4 dhcpcd[1057]: all: IPv6 kernel autoconf disabled dhcpcd[1057]: eth0: IPv6 kernel autoconf disabled dhcpcd[1057]: eth0: adding address fe80::7a45:61ff:fe08:50d4 dhcpcd[1057]: if_addaddress6: Operation not supported dhcpcd[1057]: eth0: executing `/libexec/dhcpcd-run-hooks' PREINIT dhcpcd[1057]: eth0: executing `/libexec/dhcpcd-run-hooks' NOCARRIER dhcpcd[1057]: no interfaces have a carrier dhcpcd[1057]: forking to background dhcpcd[1057]: forked to background, child pid 1067